http://videomaker.com/community/forums/ Videomaker Forums » Topic: Canon HV40 / Manfrotto problem en Mon, 23 Nov 2009 22:07:05 +0000 http://videomaker.com/community/forums/topic/canon-hv40-manfrotto-problem#post-48800 Mon, 06 Jul 2009 18:20:06 +0000 hmueller 48800@http://videomaker.com/community/forums/ <p>Well, I tried it and I could position the camcorder by ignoring the pin. One would have to tighten the screw quite a bit to make sure it does not move around on the plate.</p> <p>Thanks for the suggestion of the aluminum plate, but I am afraid that is out of my skill set :-(</p> http://videomaker.com/community/forums/topic/canon-hv40-manfrotto-problem#post-48777 Mon, 06 Jul 2009 02:09:21 +0000 jimcvideo 48777@http://videomaker.com/community/forums/ <p>Yeah, if there's enough leeway that the camera could slide farther back without the pin, I'd just remove the pin. otehrwise, I dreamed up a contraption when you mentioned this thread that was basically a piece of 3/4 inch thick aluminum with a hole bored into it. Inside that hole, use some jb weld to place a nut at one end that the tripod place can bolt into. on the other end of the plate, jb weld a bolt sticking out just far enough that you can fully seat the camera on the piece of aluminum. It would be crude, but paint it black and nobody would see it, and the 3/4" should be more than enough to give you clearance.</p> http://videomaker.com/community/forums/topic/canon-hv40-manfrotto-problem#post-48771 Sun, 05 Jul 2009 18:01:13 +0000 EarlC 48771@http://videomaker.com/community/forums/ <p>Not necessarily. The pin on all my plates can be overruled one way or another. In many cases they are flexible, or actually removed. While I recognize and appreciate their purpose, use and presence, I am not THAT dependent upon them to keep my camera in position (usually there's also somewhat skid-resistant surfacing as well) and some of my stuff doesn't even have one.</p> http://videomaker.com/community/forums/topic/canon-hv40-manfrotto-problem#post-48770 Sun, 05 Jul 2009 17:19:36 +0000 hmueller 48770@http://videomaker.com/community/forums/ <p> The slot on the plate is quite long, but the position of the camcorder on the plate is determined by the pin on the plate.</p> http://videomaker.com/community/forums/topic/canon-hv40-manfrotto-problem#post-48756 Sun, 05 Jul 2009 03:45:14 +0000 D0n 48756@http://videomaker.com/community/forums/ <p>manfrotto has some shorter quick release plates (ie the ones on the pistol grips) that should fit that head.. however your ability to micro focus by moving the plate inside the head may be compromised. just take it to a camera shop and try it out.</p> http://videomaker.com/community/forums/topic/canon-hv40-manfrotto-problem#post-48754 Sun, 05 Jul 2009 03:39:18 +0000 EarlC 48754@http://videomaker.com/community/forums/ <p>It would certainly be a bit of work (major challenge even) but with the right tools, or resource who has them and some engineering/machine shop skills, could perhaps the screw slot of the plate be extended to allow for the camera to mount farther back on the plate, thus clearing a path for battery removal/replacement?</p> <p>I could not see the top of the plate to know if the slot already extends to its possible range of placement, or if there might be enough room to go another inch or so.</p> http://videomaker.com/community/forums/topic/canon-hv40-manfrotto-problem#post-48750 Sat, 04 Jul 2009 22:40:02 +0000 hmueller 48750@http://videomaker.com/community/forums/ <p> Hi Jim</p> <p>It is a Manfrotto 701hdv. The problem is that the slide plate totally blocks the battery release clip, and does not allow the battery to be removed.<br />I took a photo - it is not very good but shows the problem.</p> <p><img src="http://hmuellerdesign.com/images/manfrottohdv40.jpg" alt="hdv 40 on Manfrotto 701 head" /></p> <p>Thanks<br />Heidi</p> http://videomaker.com/community/forums/topic/canon-hv40-manfrotto-problem#post-48734 Sat, 04 Jul 2009 05:38:50 +0000 jimcvideo 48734@http://videomaker.com/community/forums/ <p>What model tripod is it? Manfrotto makes dozens of different heads, many of which with their own unique plate.</p> <p>If you post a pic, we might be able to give you a better answer too.</p> http://videomaker.com/community/forums/topic/canon-hv40-manfrotto-problem#post-48722 Fri, 03 Jul 2009 18:40:17 +0000 hmueller 48722@http://videomaker.com/community/forums/ <p>HI</p> <p>I recently purchased a Canon HV40 and a matching Manfrotto tripod. While I am very happy with both products, I found that I could not change the battery while the camcorder was on the tripod - the slide plate on the tripod head is too long. I have to take the camcorder off, and remove the slide plate before I can replace the battery.<br />Does anyone have a solution? Is there a shorter slideplate or a spacer of some kind?</p> <p>Thanks<br />Heidi</p>